HighA26

SPN 4364 FMI 18 International A26 — NOx Sensor Fault (2026)

SPN 4364 FMI 18 on International A26 means aftertreatment scr nox conversion efficiency - data valid but below normal. 60–80% of field cases trace to contaminated or diluted def fluid. Shop repair with parts runs $200 - $4,500; DIY wiring or filter work starts at $40–$150. Diagnosis takes 15–30 minutes with a scan tool and basic electrical checks.

What This Code Means

SPN 4364 FMI 18 on International A26 tells the ECM that scr nox efficiency is outside calibrated limits. On J1939, FMI 18 specifies the failure mode: Aftertreatment SCR NOx Conversion Efficiency - Data Valid But Below Normal. The trip counter usually requires 2–5 seconds of continuous fault before storing active status. The SCR system reduces NOx by injecting DEF into hot exhaust. When conversion efficiency drops below calibrated limits, International sets SPN 4364 and inducement timers may begin counting down toward derate.

Common Symptoms

• Amber or red MIL with emissions warning (100% of cases)
• Visible white DEF crystallization at doser or exhaust (80% of cases)
• SCR inducement timer counting down (60% of cases)
• Low DEF consumption relative to miles driven (40% of cases)
• High upstream NOx with low downstream reduction in live data (25% of cases)

Likely Causes (Ranked by Probability)

1. Contaminated or diluted DEF fluid (45% of cases) — DEF below 32.5% urea concentration reduces NOx conversion and sets efficiency faults.

2. Failed DEF doser or low DEF pressure (25% of cases) — Insufficient DEF delivery at the SCR inlet prevents adequate NOx reduction.

3. Degraded or poisoned SCR catalyst (15% of cases) — Coolant leaks, oil ash, or thermal damage reduce catalyst conversion efficiency permanently.

Step-by-Step Diagnostic Guide

1. Connect ServiceMaxx and monitor upstream/downstream NOx ppm during steady 1,500 RPM — efficiency below 70% confirms SCR underperformance. — Tool: scan tool or multimeter. Document readings on the work order.

2. Test DEF concentration with refractometer — target 32.5% urea; readings below 30% cause efficiency faults. — Tool: scan tool or multimeter. Document readings on the work order.

3. Inspect DEF doser injector for crystallization and verify DEF pressure at 130–145 PSI during dosing. — Tool: scan tool or multimeter. Document readings on the work order.

4. Check exhaust for coolant smell indicating head gasket leak poisoning the SCR catalyst. — Tool: scan tool or multimeter. Document readings on the work order.

5. Verify NOx sensor readings are plausible — intake reading above 800 ppm at idle may indicate bad upstream sensor. — Tool: scan tool or multimeter. Document readings on the work order.

Repair Options (with Costs)

Repair	DIY	Independent Shop	Dealer
SCR NOx Efficiency wiring repair	$25–$150	$150–$350	$250–$500
SCR NOx Efficiency sensor/part	$200 - $4,500	$$200 - $4,500 + labor	$900+
Full module replacement	N/A	$600–$1,500	$900+

Platform-Specific Notes

On International A26, this code follows OEM J1939 diagnostic logic. Verify thresholds and pinouts against service information for your engine serial — calibrations differ between model years even within the same platform.

When This Code Sets

SPN 4364 FMI 18 sets when scr nox efficiency fails the J1939 rationality monitor for a calibrated trip counter — usually 2–5 seconds continuous on electrical faults, longer on efficiency monitors. Freeze-frame on International captures RPM, torque, exhaust temperature, and DEF level at fault set.

Scan Tool Parameters to Log

• Inlet vs outlet NOx (ppm)
• SCR efficiency %
• DEF level and quality/concentration
• DEF tank temperature

Common Misdiagnoses

Replacing SCR catalyst without testing DEF quality — Catalyst is blamed for every emissions fault.. Instead: Parts-cannon trap — test DEF at 32.5% with refractometer and verify doser pressure at 130–145 PSI first.

Replacing both NOx sensors when only one reads implausible — Sensor pairs are replaced as a set by habit.. Instead: Compare upstream vs downstream NOx at steady RPM — replace only the sensor with erratic readings.

Shop Notes from the Field

On International, always verify DEF quality and dosing before SCR catalyst replacement. Catalyst is expensive — confirm efficiency with live NOx data first.

Safety Warning

• DEF is corrosive — wear gloves and eye protection.
• Hot exhaust surfaces exceed 600°F during active regen — keep clear.

Prevention Tips

• Use API-certified DEF and store indoors above 12°F.
• Fix coolant leaks before coolant reaches the SCR brick.
• Replace DEF filters per OEM interval.

International Field Notes for SPN 4364 FMI 18

• Capture a 20-minute data log of scr nox efficiency parameter during mixed driving before closing the work order — intermittent FMI signatures need road replication, not bay-idle checks.
• Check for OEM technical service bulletins covering SPN 4364 FMI 18 on A26 — many bulletin fixes address harness routing rather than sensor replacement.
• Torque scr nox efficiency mounting fasteners per International OEM spec — verify with engine serial. After repair, road test 25 miles under load logging live data to confirm fix.
• Document ambient temperature and key-cycle count at fault set on International A26 — cold-soak faults on scr nox efficiency often clear after warm-up when moisture is the root cause.
• Compare this unit’s repair history: repeat SPN 4364 FMI 18 within 5,000 miles indicates incomplete prior repair, not a new component failure.
• If scr nox efficiency was recently replaced, verify correct part number for engine serial — superseded calibrations require matching hardware revision on International.
• Capture a 20-minute data log of scr nox efficiency parameter during mixed driving before closing the work order — intermittent FMI signatures need road replication, not bay-idle checks.
• Check for OEM technical service bulletins covering SPN 4364 FMI 18 on A26 — many bulletin fixes address harness routing rather than sensor replacement.
• Torque scr nox efficiency mounting fasteners per International OEM spec — verify with engine serial. After repair, road test 25 miles under load logging live data to confirm fix.
• Document ambient temperature and key-cycle count at fault set on International A26 — cold-soak faults on scr nox efficiency often clear after warm-up when moisture is the root cause.
• Compare this unit’s repair history: repeat SPN 4364 FMI 18 within 5,000 miles indicates incomplete prior repair, not a new component failure.
• If scr nox efficiency was recently replaced, verify correct part number for engine serial — superseded calibrations require matching hardware revision on International.

Related Codes

• SPN 3216 FMI 0 — often stacks with SPN 4364 FMI 18
• SPN 3364 FMI 9 — often stacks with SPN 4364 FMI 18

FAQ

What DEF concentration does International require?

ISO 22241 DEF at 32.5% urea — verify with a refractometer, not guesswork.

Can bad DEF cause SPN 4364?

Yes — diluted, contaminated, or expired DEF is the most common root cause.

How is SCR efficiency calculated?

ECM compares upstream vs downstream NOx sensor readings during steady-state operation.

What does SPN 4364 FMI 18 mean on International A26?

SPN 4364 FMI 18 means aftertreatment scr nox conversion efficiency - data valid but below normal. The ECM detected scr nox efficiency outside calibrated limits. Verify with freeze-frame data before clearing.

Can I drive with SPN 4364 FMI 18 active?

Short distances only if power is normal. Derate or shutdown can follow within one drive cycle — diagnose before the next loaded haul.

How much does it cost to fix SPN 4364 FMI 18?

DIY repairs start at $40–$150 for wiring or filters. Shop repairs with parts run $200 - $4,500. Dealer pricing runs $900+.

What is the most common cause of SPN 4364 FMI 18?

Contaminated or diluted DEF fluid — confirm with visual inspection and live data before ordering parts.

Sources

• SAE J1939-71 — SPN 4364 parameter definition
• International OEM service information — verify by engine serial
• Mitchell1 ProDemand — 2026 labor and parts cost surveys

Related Reading

• International fault codes hub
• Diesel repair cost estimator
• SCR NOx Efficiency diagnostic guide
• SPN 3216 FMI 0
• SPN 3364 FMI 9