Medium6.7L

P0671 Ford Powerstroke 7.3L/6.7L — Glow Plug Circuit (2026)

P0671 on Ford Powerstroke 6.7L means cylinder 1 glow plug circuit/open. 60–80% of field cases trace to wiring or connector fault. Shop repair with parts runs $40 - $1,200; DIY wiring or filter work starts at $40–$150. Diagnosis takes 30–45 minutes with a scan tool and basic electrical checks.

What This Code Means

P0671 on Ford Powerstroke 6.7L tells the ECM that glow plug cylinder 1 is outside calibrated limits. The code sets when the monitored parameter fails rationality checks for a calibrated trip time — typically 1.4–4 seconds continuous on OBD-II diesel platforms. On Ford Power Stroke, P0671 means Cylinder 1 Glow Plug Circuit/Open. Prove the system with live data on FORScan before replacing parts. This page covers symptoms, causes, tests, and common misdiagnoses.

Common Symptoms

• Malfunction indicator lamp illuminated (100% of cases)
• Power loss, rough running, or limp mode under load (80% of cases)
• Related aftertreatment or fuel-system complaints depending on code family (60% of cases)
• Code returns after clearing if root cause remains (40% of cases)

Likely Causes (Ranked by Probability)

1. Wiring or connector fault on Glow Plug Cylinder 1 (45% of cases) — Pull the connector, check for green corrosion and bent pins. Wiggle test while watching live data on Glow Plug Cylinder 1.

2. Failed Glow Plug Cylinder 1 (25% of cases) — Compare scan tool reading to mechanical test or bi-directional command. No response with good wiring confirms hardware failure.

3. ECM calibration or software issue (15% of cases) — Check for available ECM updates before replacing sensors. Outdated cal causes false readings.

4. Low system voltage or ground fault (10% of cases) — Measure supply at connector key-on — expect 11.8–14.4 VDC. Bad ground adds 0.5–2V error to sensor readings.

5. Mechanical root cause (leak, restriction, bind) (5% of cases) — Verify mechanical function before condemning the sensor — stuck actuators and clogged lines mimic sensor codes.

Step-by-Step Diagnostic Guide

1. Scan with FORScan and save freeze-frame for P0671. — Tool: scan tool or multimeter. Document readings on the work order.

2. Inspect connectors and harness for the glow plug cylinder 1. — Tool: scan tool or multimeter. Document readings on the work order.

3. Compare PID values to mechanical gauges or known-good ranges. — Tool: scan tool or multimeter. Document readings on the work order.

4. Repair the proven fault, then verify with a loaded drive cycle. — Tool: scan tool or multimeter. Document readings on the work order.

Repair Options (with Costs)

Repair	DIY	Independent Shop	Dealer
Glow Plug Cylinder 1 wiring repair	$25–$150	$150–$350	$250–$500
Glow Plug Cylinder 1 sensor/part	$40 - $1,200	$$40 - $1,200 + labor	$300+
Full module replacement	N/A	$600–$1,500	$300+

Platform-Specific Notes

7.3L (1999–2003): HEUI — Follow ford-powerstroke OEM diagnostic tree for P0671 on 7.3L.

6.0L (2003–2007): HEUI/FICM — Follow ford-powerstroke OEM diagnostic tree for P0671 on 6.0L.

6.4L (2008–2010): Common-rail — Follow ford-powerstroke OEM diagnostic tree for P0671 on 6.4L.

6.7L (2011–2026): CP4.2 common-rail — Follow ford-powerstroke OEM diagnostic tree for P0671 on 6.7L.

When This Code Sets

P0671 typically stores after the ECM detects glow plug cylinder 1 outside calibrated limits for 1.4–4.0 seconds (OBD-II trip). Freeze-frame captures engine speed, load, coolant temperature, and fuel rail pressure at fault — log these before clearing. Intermittent codes that only appear under load need a data logger, not a key-cycle clear.

Scan Tool Parameters to Log

• Glow Plug Cylinder 1 live data PID at idle, cruise, and full load
• Battery voltage and ECM supply voltage
• Related aftertreatment and protection PIDs (SPN 1569 if stacked)

Common Misdiagnoses

undefined — undefined. Instead: undefined

undefined — undefined. Instead: undefined

undefined — undefined. Instead: undefined

Shop Notes from the Field

Shop tip (Ford Power Stroke P0671): Do not quote the expensive assembly from the code name alone. Confirm live data rationality and wiring first.

Prevention Tips

• Replace fuel filters at OEM interval — restricted filters cause 30% of glow plug cylinder 1 codes on pickup platforms.
• Use API-certified DEF and diesel fuel; contamination triggers aftertreatment efficiency faults within one tank.
• Complete parked regens — interrupted regen is the leading preventable DPF restriction cause.
• Document scan tool readings on every repair — warranty and fleet audits require parameter snapshots.

Ford Powerstroke Field Notes for P0671

• Capture a 20-minute data log of glow plug cylinder 1 parameter during mixed driving before closing the work order — intermittent FMI signatures need road replication, not bay-idle checks.
• Check for OEM technical service bulletins covering P0671 on 6.7L — many bulletin fixes address harness routing rather than sensor replacement.
• Torque glow plug cylinder 1 mounting fasteners per Ford Powerstroke OEM spec — verify with engine serial. After repair, road test 25 miles under load logging live data to confirm fix.
• Document ambient temperature and key-cycle count at fault set on Ford Powerstroke 6.7L — cold-soak faults on glow plug cylinder 1 often clear after warm-up when moisture is the root cause.
• Compare this unit’s repair history: repeat P0671 within 5,000 miles indicates incomplete prior repair, not a new component failure.
• If glow plug cylinder 1 was recently replaced, verify correct part number for engine serial — superseded calibrations require matching hardware revision on Ford Powerstroke.
• Capture a 20-minute data log of glow plug cylinder 1 parameter during mixed driving before closing the work order — intermittent FMI signatures need road replication, not bay-idle checks.
• Check for OEM technical service bulletins covering P0671 on 6.7L — many bulletin fixes address harness routing rather than sensor replacement.
• Torque glow plug cylinder 1 mounting fasteners per Ford Powerstroke OEM spec — verify with engine serial. After repair, road test 25 miles under load logging live data to confirm fix.
• Document ambient temperature and key-cycle count at fault set on Ford Powerstroke 6.7L — cold-soak faults on glow plug cylinder 1 often clear after warm-up when moisture is the root cause.
• Compare this unit’s repair history: repeat P0671 within 5,000 miles indicates incomplete prior repair, not a new component failure.
• If glow plug cylinder 1 was recently replaced, verify correct part number for engine serial — superseded calibrations require matching hardware revision on Ford Powerstroke.

Related Codes

FAQ

What does P0671 mean on Ford Power Stroke?

Cylinder 1 Glow Plug Circuit/Open. Confirm with live data before replacing parts.

Can I drive with P0671?

Short trips may be possible, but continued hard pulls risk limp mode or aftertreatment damage. Diagnose promptly.

What tools should I use?

FORScan, Ford FDRS/IDS, Multimeter.

What does P0671 mean on Ford Powerstroke 6.7L?

P0671 means cylinder 1 glow plug circuit/open. The ECM detected glow plug cylinder 1 outside calibrated limits. Verify with freeze-frame data before clearing.

Can I drive with P0671 active?

Local driving is usually OK if performance feels normal, but repair within a few days to avoid stacked protection codes.

How much does it cost to fix P0671?

DIY repairs start at $40–$150 for wiring or filters. Shop repairs with parts run $40 - $1,200. Dealer pricing runs $300+.

What is the most common cause of P0671?

Wiring or connector corrosion — confirm with visual inspection and live data before ordering parts.

Sources

• OEM service information — Ford Powerstroke 6.7L diagnostic procedures
• SAE J2012 — OBD-II DTC definition for P0671
• Mitchell1 ProDemand — 2026 labor and parts cost surveys

Related Reading

• Ford Powerstroke fault codes hub
• Diesel repair cost estimator
• Glow Plug Cylinder 1 diagnostic guide